IDENTIFICATION OF THE COMPANY AND OF THE MATERIAL
CuP Alloys (Metal Joining) Ltd
Unit 36 Matrix Business Centre
Phone No 01909 547248
Fax No. 01909 547001
Product Type Liquid Soldering Flux
INFORMATION ON INGREDIENTS
This material is defined as a mixture.
C.R34 Xn. R22. N. R50/53
Xn R22 Xi. R36
C;Corrosive. N; Dangerous to the environment.
Most important Hazards
R20/21 Harmful by inhalation and ingestion
R36/38 Irritating to eyes and skin
Potential Acute Health Effects
Inhalation Irritation, coughing, sore throat
Eye Contact Smarting, soreness, irritation
Skin Contact Itching, stinging, sore on cuts
Ingestion Excessive saliva, nausea, vomiting.
Potential Chronic Health Effects Fluorine poisoning
Environmental Hazard Not Available
FIRST AID MEASURES
Inhalation Treat for shock
Ingestion Administer large volumes of milk or caicium gluconate. Treat for shock and transfer to hospital stating "suspected fluorine poisoning"
Eye Contact S26 Irrigate thoroughly with water and seek medical advice.
Skin Contact Wash thororoughly with water.
FIRE FIGHTING MEASURES
Material is not combustible. Fluorine bearing fumes may be evolved. Wear breathing apparatus.
ACCIDENTAL RELEASE MEASURES
Personal Precautions See Section 8
Environmental Precautions Treat with slaked lime
Clean up methods As appropriate
HANDLING & STORAGE
Storage S2 Keep out of reach of children
S13 Keep away from all foodstuffs
8) EXPOSURE CONTROL/PERSONAL PROTECTION
UK Occupational Exposure Standards are:
Fume Long Term Short Term
8-hour TWA* Value 15 minute Value
Hydrogen Fluoride (as F) - 2.5mg/m3
Fluoride (as Fluorine) 2.5mg/m3 -
Boron Trifluoride - 3mg/m3
* Time Weighted Average
Avoid exposure to fume with good ventilation or local extraction. If a risk of inhalation exists, personal
respiratory protection should be worn. Safety glasses should be worn as well as impervious gloves to
prevent skin contact. Wash hands after using this material. The use of protective clothing is recommended
Personal Protection Wear Suitable hand protection
Wear Goggles and overalls
Ensure adequate ventilation
S20/21 Do not eat drink or smoke when using
S22 Do not inhale dust
S23 Do not inhale fumes
S45 in case of accident or feeling unwell seek medical advice
Exposure Limits HF TLV 2mg/cubic metre
BF TLV 3mg/cubic metre.
PHYSICAL & CHEMICAL PROPERTIES
State Solid Powder/Paste
Melting Point 550 deg C
Boiling Point Not Available
Vapour Pressure Not Available
Explosive Risks Not Applicable
Flammability Risks Not Applicable
STABILITY & REACTIVITY
Containers of powder left open once the seals are broken may absorb moisture and become lumpy. Pastes
are water based and, whilst stable, will lose water by evaporation if left open. Avoid contact with acids and
strong oxidising agents.
No other adverse reactions are known
Inhalation Not Available
Eye Contact Not known
Skin Contact Not known
Target Organs Not known
Chronic Effects Non known
Carcinogenic Effects None
Mutagenic Effects None
Teratogenic Effects Not available
Narcosis Not available
Toxicological data for these preparations: LD50(oral - rat) > 200mg/kg.
Classified as moderately irritating, according to Draize skin test.
Likely to be harmful to all species of animal life. As far as is known no other threat is posed to the
Waste must be disposed of in accordance with Environmental Protection Act and Integrated Pollution Act. Seek advice from a licensed contractor.
No special precautions
20/22 Harmful by inhalation and if swallowed.
36/38 Irritating to eyes and skin.
2 Keep out of reach of children.
13 Keep away from food, drink and animal feed stuffs.
20/21 When using do not eat, drink or smoke.
22/23 Do not breathe dust or fumes.
26 In case of eye contact, rinse immediately with water and seek medical advice.
45 In case of feeling unwell seek medical attention.
References Not Available
NB The information contained in this sheet is believed to be accurate, but CuP Alloys (Metal Joining) Ltd assumes no liability for its accuracy or completeness. Final determination of the suitability of a product remains the responsibility of the user.