IDENTIFICATION OF THE COMPANY AND OF THE MATERIAL: REVISION 01 24.01.18.
CuP Alloys (Metal Joining) Ltd
Unit 36 Matrix Business Centre
Phone No 01909 547248
Fax No. 01909 547001
Contacts Shaun Meakin, Glen Farrell. Email email@example.com
Product description and usages; A white powder or paste suitable for brazing similar or dissimilar parent metals (except aluminium) in conjuncyion with silver solders with a melting point below 750 degC.
EF Flux Powder.
EF Flux Paste.
SERIOUS HEALTH HAZARD. HEALTH HAZARD/HAZARDOUS TO THE OZONE LAYER.
SIGNAL WORD Warning
HAZARD-DETERMINING COMPONENTS OF LABELING;
H302 Harmful if swallowed.
H312 Harmful if in contact with skin.
H332 Harmful if inhaled.
H361 Suspected of damaging fertilityn or the unborn child. Route of exposure - oral.
P201 Obtain special instructions.
P202 Do not handle until all safety precautions have been read and understood.
P261 Avoid breathing dust.
P264 Wash thoroughly after handling.
P280 Wear protective gloves/protective clothing/protective eyewear.
P270 Do not eat, drink or smoke when using this product.
P271 Use only outdoors or in a well well-ventilated area.
P302+P352 IF ON SKIN Wash with plenty of soap and water.
P304+P340 IF IN HALED Remove person to fresh air and keep comftable for breathing.
P301+P312 IF SWALLOWED Call a POISON CENTRE / Doctor if you feel unwell.
P330 Rinse mouth.
P308+313 If exposed or concerned seek medical advice / attention.
P405 Store locked up.
P501 Dispose of container in accordance with loca/regiona/international regulations.
OTHER HAZARDS WHICH DO NOT RESULT IN GHS CLASSIFICATION;
Heat rays (infrared radiation) from flame or hot metal ca injure eyes. Overexposure to brazing fumes and gases can be hazardous. Read and understand supplier's instructions, Safety Data Shhet and precautionary labels before useing this product.
INFORMATION ON INGREDIENTS
||Applicable 'R/ Phases
||20 - 30
|For the listed ingredients the identity and/or exact percentages are being withheld as a trade secret.
FIRST AID MEASURES
AFTER INHALATION; Move to fresh air if breathing is difficult. If breathing has stopped perform artificial respiration and seek immediate medical assistance.
AFTER SKIN CONTACT; Rub in calcium gluconate solution or gel immediately. Remove contaminated clothing and wash the skin thoroughly with soap and water. For reddened or blistered skin, or thermal burns, obtain medical assistance at once.
AFTER EYE CONTACT; Dust or fume from this product should be flushed from the eyes with copious amounts of clean, tepid water until transported to a medical facility.Do not allow victim to rub or keep eyes tightly closed. Obtain medical assistance at once.
AFTER SEALLOWING; Rinse out the mouth and then drink plenty of water. Do not induce vomiting. Immediately seek medical assistance.
MOST IMPORTANT SYMPTONS AND EFFECTS, BOTH ACUTE AND DELAYED; Nausea. Gastric or intestinal disorders when ingested. Breathing difficulty. Coughing.
INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT NEEDED; Treat symptomatically. Medical supervision for at least 48 hours.
FIRE FIGHTING MEASURES
Material is not combustible. Fluorine bearing fumes may be evolved. Wear breathing apparatus.
ACCIDENTAL RELEASE MEASURES
Personal Precautions See Section 8
Environmental Precautions Treat with slaked lime
Clean up methods As appropriate
HANDLING & STORAGE
Storage S2 Keep out of reach of children
S13 Keep away from all foodstuffs
8) EXPOSURE CONTROL/PERSONAL PROTECTION
UK Occupational Exposure Standards are:
Fume Long Term Short Term
8-hour TWA* Value 15 minute Value
Hydrogen Fluoride (as F) 1.5mg/m3 - 2.5mg/m3
Fluoride (as Fluorine) 2.5mg/m3 -
* Time Weighted Average
Avoid exposure to fume with good ventilation or local extraction. If a risk of inhalation exists, personal
respiratory protection should be worn. Safety glasses should be worn as well as impervious gloves to
prevent skin contact. Wash hands after using this material. The use of protective clothing is recommended
- Personal Protection Wear Suitable hand protection
GENERAL PERSONAL PROTECTIVE AND HYGENIC MEASURES; The usual precautionary measures for handling chemicals should be followed. Determine the quality and composition of fumes and gases to which workers are exposed by taking an air sample from within the brazer's helmet or in the brazers working zone. Improve ventilation if exposure limits are exceeded. Keep away from food, beverages and feed.
VENTILATION; Use enough ventilatiom , loccal exhaust at the flame or heat source, to keep the fumes and gases out of the brazer's breathing zone and general area. An approved respirator should be used unless exposure assesments are below applicable exposure limits.
PROTECTION OF HANDS; Use thermally protective gloves. Suitable gloves can be recommended by the glove supplier. The glove material has to be impermiable and resistant to the product/the preparation.
EYE PROTECTION; Wear glasses or goggles or face shield with apropriate shading for the brazing operations.
BODY PROTECTION; Wear protective work clothing.
PHYSICAL & CHEMICAL PROPERTIES
APPEARANCE; White powder.
ODOR THRESHOLD; Product has no odor so not aplicable.
pH VALUE; Not applicable.
MELTING POINT/ MELTING RANGE; 500-850 DegC.
BOILING POINT; No data available.
FLASH POINT; No data available.
FLAMMABILITY; No data available.
AUTO IGNITION TEMPERATURE; No data available.
DECOMPOSITION TEMPERATURE; No data available.
DANGER OF EXPLOSION; Product does not present an explosion hazard.
EXPLOSION LIMITED; No data available.
VAPOUR PRESSURE; No data available.
RELATIVE DENSITY; 1.5-1.7.
VAPOUR DENSITY; No data available.
EVAPORATION RATE; Not applicable.
SOLUBILITY IN WATER; Negligible.
PARTITION COEFFIENT (N0OCTANOL/WATER0; No data available.
VISCOSITY; No data available.
OTHER INFORMATION; No other relevant information availabe.
STABILITY & REACTIVITY
Containers of powder left open once the seals are broken may absorb moisture and become lumpy. Pastes
are water based and, whilst stable, will lose water by evaporation if left open. Avoid contact with acids and
strong oxidising agents.
No other adverse reactions are known
Inhalation Not Available
Eye Contact Not known
Skin Contact Not known
Target Organs Not known
Chronic Effects Non known
Carcinogenic Effects None
Mutagenic Effects None
Teratogenic Effects Not available
Narcosis Not available
Toxicological data for these preparations: LD50(oral - rat) > 200mg/kg.
Classified as moderately irritating, according to Draize skin test.
Likely to be harmful to all species of animal life. As far as is known no other threat is posed to the
Waste must be disposed of in accordance with Environmental Protection Act and Integrated Pollution Act. Seek advice from a licensed contractor.
No special precautions
20/22 Harmful by inhalation and if swallowed.
36/38 Irritating to eyes and skin.
2 Keep out of reach of children.
13 Keep away from food, drink and animal feed stuffs.
20/21 When using do not eat, drink or smoke.
22/23 Do not breathe dust or fumes.
26 In case of eye contact, rinse immediately with water and seek medical advice.
45 In case of feeling unwell seek medical attention.
References Not Available
NB The information contained in this sheet is believed to be accurate, but CuP Alloys (Metal Joining) Ltd assumes no liability for its accuracy or completeness. Final determination of the suitability of a product remains the responsibility of the user.